Showing results: 91 - 105 of 440 items found.
-
DT1 -
North Atlantic Industries
The DT1 module features 24 programmable channels for either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3 – 60 VCC source. These modules can sense broken input connections and whether an input is shorted to +VCC or to ground.
-
779647-31 -
NI
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
AC3 -
North Atlantic Industries
The module is used to provide an AC signal source when a secondary reference source other than the optional on-board reference module is required. The modules are programmable for full range voltage outputs from 2 to 115 VAC, and frequency from 47 Hz to 10 kHz.
-
AC2 -
North Atlantic Industries
The module is used to provide an AC signal source when a secondary reference source other than the optional on-board reference module is required. The modules are programmable for full range voltage outputs from 2 to 115 VAC, and frequency from 47 Hz to 10 kHz.
-
VLF Series -
High Voltage Inc.
VLF hipots perform voltage withstand tests and provide the voltage source for diagnostic cable testing. There is no better method for verifying the AC integrity of a cable than applying VLF AC voltage. Tan delta and partial discharge measurement accessories are frequently purchased along with VLF equipment to extend their capabilities.
-
CIS -
MeterTest Ltd.
The CIS current integrated source was designed to provide a stable alternating current source for the electricity meter test equipment, and in laboratories. The output current is isolated and independent from the mains voltage. Different CIS versions are available depending upon the values of output power and output current required.
-
BV0023B -
Keysight Technologies
The PathWave BenchVue USB modular SMU pro software configures voltage and current source, range and limit for each SMU channel and log unrestricted data.
-
TOMSAD
Power stabilized POWERLAB series are high precision current sources with variable voltage and current over the entire range . They can operate in different modes of stabilization voltage or current switched automatically with adjustable limit value of the load current at any point in the range.
-
ADC Corporation
Voltage source of ±1000V, high-speed measurement up to 1000 readings/sec, current measurement resolution of 1fA, resistance measurement range 3x1017Ω and 5 1/2-digit display
-
Changzhou Applent Instruments Inc.
Not only a Capacitance Meter but also Insulation Meter. Numerical controlled voltage source has improved the sampling speed. Both the capacitance and transistor leakage current can be tested.
-
Core Technology Group
Power for Core Technology Group Signal Chain ProductsFlexible bi-polar voltage converter using low cost connectorsDriving multiple devicesIndustrial +/- 10 volt power source
-
72-13540 -
Tenma
*USB tester inspects USB charger & portable power source*Lightweight and portable*LCD backlight*High/low output voltage warning*10 sets of data memory
-
AC6802B -
Keysight Technologies
This basic AC power source offers stable, reliable power up to 1000 VA. An intuitive user interface and flexible I/O connectivity. Increase your uptime with stable, reliable AC power source Engineer reliability into your designs with a basic AC power source. Test your designs with confidenceTest under real-world conditions - fluctuating voltage or transient spikes. Easily access setup and measurement information
-
JYV-40 -
Kingrun Instrument Co., Ltd.
JYV-40 segment voltage test equipment is made up of constant current source, voltage-checking circuit and control circuit. The output current is adjustable and stable. Measured voltage value can be shown by three and half digital voltmeter, it can test the DC interturn and segment voltage and also is the effective way of checking turn coil resistance equilibrium.
-
40-413-002 -
Pickering Interfaces Ltd.
A 32 channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only, a low side only (shown here)and a combined high and low side each capable of driving 2A loads. Each output is fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side voltage driving the high side voltage source is supplied from an external voltage source, permitting the module to drive high capacity loads without impacting the PXI chassis power supply.